|
Subject |
Author |
Date Posted |
Forum
|
 |
RE: 2004 2500 series Bigfoot

Congratulations on the new to you Bigfoot! Enjoy!
|
bigfootgrey
|
08/17/23 01:29pm |
Truck Campers
|
 |
RE: Happijac motors

https://i.imgur.com/RNxjV0Kl.jpg
Here’s my 2008 bracket. New bracket has more bracing and jack mounts slightly lower
|
bigfootgrey
|
02/19/23 12:45pm |
Truck Campers
|
 |
RE: Happijac motors

https://i.imgur.com/7O62Xghl.jpg
Here’s a picture of Bigfoot’s front brackets for the new motor
|
bigfootgrey
|
02/19/23 12:42pm |
Truck Campers
|
 |
RE: Happijac motors

Thanks Makito
I appreciate the update. Sounds like there are a couple of options. Nice to be able to use the old board with both motor styles
|
bigfootgrey
|
02/16/23 10:08am |
Truck Campers
|
 |
RE: Happijac motors

Thanks Beagle
I’ll measure when it’s back on the truck. We’re camping with it off the truck for the next couple of weeks
Should be close but I might drill if I have to but it is only when folded in. Good to know about the board. Always careful at end of travel too. I could move the rear motors to the front as long as I can run new and old together on the board
|
bigfootgrey
|
02/15/23 07:25pm |
Truck Campers
|
 |
RE: Happijac motors

https://i.imgur.com/4rqFkl7l.png
This is what e trailer shows for clearance measurement.
|
bigfootgrey
|
02/15/23 02:47pm |
Truck Campers
|
 |
RE: Happijac motors

I also spoke with Bigfoot Industries regarding the clearance issue for the new jack motors and they had to alter the jack mount to the swing out brackets to achieve clearance. This lowered the jack height to the road a few inches. Happijac says the new style motors are 8” above the top of the jack
I have a Bigfoot 10.4, 2008, same as you. I recently replaced the jacks with 4800, and at the time measured the motor clearance thinking I might need new motors. As I recall, I decided they would fit. My old motors still worked so I didn't change them. I'll measure them again but pretty sure you don't have an issue.
I replaced my front jacks with4800’s. The rear jacks are original 4150’s from 2008. If the clearance is ok for the fronts to swing in under the cab over that would be great. Does the control board need to be changed? Mine is original,with the cord.
|
bigfootgrey
|
02/15/23 11:28am |
Truck Campers
|
 |
RE: Happijac motors

I also spoke with Bigfoot Industries regarding the clearance issue for the new jack motors and they had to alter the jack mount to the swing out brackets to achieve clearance. This lowered the jack height to the road a few inches. Happijac says the new style motors are 8” above the top of the jack
|
bigfootgrey
|
02/13/23 01:29pm |
Truck Campers
|
 |
RE: Happijac motors

Please keep us posted on your results! Hope it works !
|
bigfootgrey
|
02/12/23 11:29am |
Truck Campers
|
 |
RE: Happijac motors

I spoke with Happijac recently about the same scenario. I was first told they were going to bring the old style back. Then I was told they weren’t and I needed all new jacks, motors and controller if one old style motor failed. I told them about the clearance issue for the front swing out brackets and they really didn’t seem to care.Lots of campers out there with clearance issues. Great customer service! I have one motor that’s hanging in there for now.
|
bigfootgrey
|
02/12/23 11:19am |
Truck Campers
|