Good Sam Club Open Roads Forum: Tech Issues: Tee Moulding
Open Roads Forum Already a member? Login here.   If not, Register Today!  |  Help

Newest  |  Active  |  Popular  |  RVing FAQ Forum Rules  |  Forum Posting Help and Support  |  Contact  

Search:   Advanced Search

Search only in Tech Issues

Open Roads Forum  >  Tech Issues

 > Tee Moulding

Reply to Topic  |  Subscribe  |  Print Topic  |  Post New Topic  | 
agesilaus

North Florida

Senior Member

Joined: 05/06/2008

View Profile



Good Sam RV Club Member

Offline
Posted: 06/07/21 02:25pm Link  |  Quote  |  Print  |  Notify Moderator

How do you keep this moulding in the slot? I have a couple of piece that came off and do not want to stay in. Brads? Glue?


Arctic Fox 25Y Travel Trailer
2012 Ford F-350 4WD Lariat 6.7L
Straightline dual cam hitch
400W Solar with Victron controller
Superbumper


opnspaces

San Diego Ca

Senior Member

Joined: 12/22/2004

View Profile


Offline
Posted: 06/07/21 03:43pm Link  |  Quote  |  Print  |  Notify Moderator

It's best to just replace with new molding.
Amazon

* This post was edited 06/07/21 03:53pm by opnspaces *


2001 Suburban 4x4. 6.0L, 4.10 3/4 ton
2005 Jayco Jay Flight 27BH
1986 Coleman Columbia Popup.

BarneyS

S.E. Lower Michigan

Moderator

Joined: 10/16/2000

View Profile



Posted: 06/07/21 05:31pm Link  |  Quote  |  Print  |  Notify Moderator

Moved to Tech Issues forum from DIY.

Darklock

Georgia

New Member

Joined: 01/06/2021

View Profile


Offline
Posted: 06/08/21 06:54am Link  |  Quote  |  Print  |  Notify Moderator

I had this problem. When build, for some reason they put silicone in there to hold the molding in. When it needed replaced, I had to scrape all of the old silicone out of the grooves to get the new molding to stay in at road speeds. Talk about a pain in the butt.

capacitor

California

Senior Member

Joined: 10/24/2020

View Profile


Offline
Posted: 06/08/21 08:33am Link  |  Quote  |  Print  |  Notify Moderator

Normally, the silicone is only used at the ends and 90’s.

Edit: OP, do you mean the moulding that goes from carpet to linoleum and slips in a track?

* This post was edited 06/08/21 09:08am by capacitor *

agesilaus

North Florida

Senior Member

Joined: 05/06/2008

View Profile



Good Sam RV Club Member

Offline
Posted: 06/08/21 09:26am Link  |  Quote  |  Print  |  Notify Moderator

Quote:

Edit: OP, do you mean the moulding that goes from carpet to linoleum and slips in a track?


No, one is around the bathroom sink and the other around a small cabinet top

capacitor

California

Senior Member

Joined: 10/24/2020

View Profile


Offline
Posted: 06/08/21 09:34am Link  |  Quote  |  Print  |  Notify Moderator

Can you post a picture?

capacitor

California

Senior Member

Joined: 10/24/2020

View Profile


Offline
Posted: 06/08/21 10:37am Link  |  Quote  |  Print  |  Notify Moderator

Ahh, counter top edge molding. Use silicone and duct tape to hold it till dry.

RLS7201

Beautyful Downtown Gladstone, MO

Senior Member

Joined: 10/26/2002

View Profile


Online
Posted: 06/08/21 03:41pm Link  |  Quote  |  Print  |  Notify Moderator

My "T" molding is held in place with small staples at the bottom edge.

Richard


95 Bounder 32H F53
460/528 stroker
Web Master
MWPSchooners.com
First brake job
1941 Hudson


Darklock

Georgia

New Member

Joined: 01/06/2021

View Profile


Offline
Posted: 06/09/21 06:13am Link  |  Quote  |  Print  |  Notify Moderator

Oops, I was thinking the trim piece cover screws on outside of trailer.

Reply to Topic  |  Subscribe  |  Print Topic  |  Post New Topic  | 

Open Roads Forum  >  Tech Issues

 > Tee Moulding
Search:   Advanced Search

Search only in Tech Issues


New posts No new posts
Closed, new posts Closed, no new posts
Moved, new posts Moved, no new posts

Adjust text size:




© 2021 CWI, Inc. © 2021 Good Sam Enterprises, LLC. All Rights Reserved.